Water Drying Oven in Ludhiana, Punjab
SEW Surface Coating Pvt. Ltd. designs, manufactures and installs water drying ovens (WDO) for manufacturers in Ludhiana, Punjab. Every plant is built at our own works in Pune, Maharashtra, then erected and commissioned at your site in Ludhiana.
After pretreatment, components must be completely dry before they enter the powder coating or painting booth. A water drying oven is an enclosed, insulated chamber with air-circulating blowers and a heating system that removes all moisture quickly and evenly. We build it to match your pretreatment plant, conveyor and production rate.
- In-Line, Batch & Conveyorised
- Camel Back for Low Heat Loss
- Matched to Pretreatment
- Supplied across Ludhiana
Water Drying Ovens for Ludhiana's Manufacturing Industry
Ludhiana is India's bicycle and cycle-parts capital and a major centre for hand tools, auto parts, sewing machines and agricultural implements. Thousands of small and medium units work in the Focal Point phases, Industrial Areas A and B, and Dhandari Kalan.
In Ludhiana, demand for water drying ovens comes mainly from cycle and two-wheeler part makers, automotive and component makers and agricultural equipment makers. Water left in seams, holes and folds after the final rinse causes blistering, pin-holes and poor adhesion once the part is coated. A correctly sized drying oven removes that moisture completely, so every part reaches the coating booth dry and at a steady temperature.
Cycle, tool and implement makers here need high-volume coating of tubular and fabricated parts. Ludhiana is about 1,750 km from our Pune works by road.
Types of Water Drying Ovens We Supply in Ludhiana
In-Line With Dip Pretreatment
A tank-type oven placed in line with the dip pretreatment tanks. The same hoist or transporter that dips the basket loads it into the oven.
- Hoist or wagon puts the basket in and takes it out
- Tank type construction
- Pneumatic or hydraulic doors
Best for: Dip pretreatment plants with hoist or transporter.
Batch Type Water Drying Oven
After pretreatment, components are loaded on a trolley and the trolley is pushed into the oven to dry off the water.
Best for: Batch plants, large components and lower volumes.
Conveyorised Conventional WDO
The conveyor carries articles through the insulated chamber for a set time and brings them out continuously, dry and ready for coating.
Best for: Spray pretreatment lines feeding a conveyorised coating booth.
Conveyorised Camel Back WDO
Works like a conveyorised oven, but the article entry and exit are cut out parallel to the ground so hot air stays inside and heat loss is reduced.
Best for: Continuous lines where fuel saving matters.
Where the Water Drying Oven Fits in Your Line
The water drying oven sits between pretreatment and the coating booth:
- PretreatmentDegreasing, de-rusting, phosphating and rinses.
- DM Water RinseFinal rinse leaves a clean, salt-free surface.
- Water Drying OvenHot air circulation removes all moisture.
- Coating BoothDry parts move on to powder or liquid coating.
- Curing OvenThe coating is baked to its final finish.
Oven temperature, size and residence time are calculated from your component weight, conveyor speed and the fuel available at your site.
Equipment Supplied With the Water Drying Oven
Pretreatment Plant
Dip or spray pretreatment cleans and phosphates the metal surface so the coating adheres well and resists corrosion.
Transporter System
PLC-controlled transporter that moves jobs through the tanks on a programmed cycle, giving priority to critical tanks.
Powder Coating Booth
Electrostatic powder booth with mono-cyclone or multi-cyclone recovery and after filter unit.
Oil Skimmer
Continuously removes floating oil from the degreasing tank, so the chemical lasts longer and parts come out cleaner.
Sludge Separator
Separates phosphate sludge from the bath to keep the process stable and cut tank-cleaning downtime.
Air Agitator
Keeps the bath moving for even temperature and chemical concentration around every component.
Industries in Ludhiana That Use Our Water Drying Ovens
Bicycles & Cycle Parts
Ludhiana makes most of India's bicycles and cycle parts.
Typical requirement: Batch or in-line WDO sized to the pretreatment plant and output.
Auto Parts
Auto part makers supply OEMs and the replacement market.
Typical requirement: Conveyorised camel back WDO after spray pretreatment.
Agricultural Implements
Implement makers serve Punjab's large farm economy.
Typical requirement: Batch or in-line WDO sized to the pretreatment plant and output.
Hand Tools & Engineering
Hand tool and machinery makers process forged and fabricated parts.
Typical requirement: In-line WDO with dip pretreatment and transporter for heavy jobs.
Steel Products
Mandi Gobindgarh's steel units supply structural products.
Typical requirement: Large in-line or batch WDO for long members.
Water Drying Oven Specifications
| Oven types | In-line with dip pretreatment, batch type, conveyorised conventional, conveyorised camel back |
|---|---|
| Construction | Enclosed insulated chamber with air-circulating blowers |
| Doors | Pneumatic or hydraulic doors for in-line tank type ovens |
| Material handling | Hoist, wagon, transporter, trolley or overhead conveyor |
| Heating | Heating system selected to suit the fuel available at your site |
| Energy saving | Camel back design, Waste Heat Recovery System (WHRS) and solar-assisted heating |
| Controls | Temperature controllers; PLC and SCADA on request |
| Scope of supply | Design, manufacturing, erection and commissioning |
Final configuration is fixed after we study your component drawings, production rate and available floor space.
From Our Pune Works to Ludhiana
Plants for Ludhiana are fabricated and pre-assembled at our factory in Ranje, Pune, about 1,750 km away by road. Equipment is dispatched by road and erected at your site by our team, followed by commissioning and trial runs.
- Site visit and study of components, production rate and space
- Plant layout and process design in minimum floor space
- Fabrication and assembly at our Pune factory
- Dispatch, erection and commissioning at your site
- Trial runs and after-sales service support
Why Buyers in Ludhiana Choose SEW Surface Coating
In-house manufacturing since 1996
Our own fabrication unit in Pune gives one-roof control over design, quality and delivery commitments.
25+ years in coating systems
More than two and a half decades of experience in powder and liquid painting systems for automobile, appliance, electrical, furniture and other industries.
Layouts in minimum space
We specialise in fitting a complete line into the floor space you actually have.
Low running cost
Plants are engineered for low fuel consumption, with options such as camel back ovens, solar-assisted heating and Waste Heat Recovery Systems (WHRS).
Modern technology
Nano-technology spray pretreatment, PLC-controlled transporters and SCADA monitoring are part of our installed base.
Erection to after-sales
We stay with the project from plant purchase through erection, commissioning and service support.
Industrial Areas We Serve in and Around Ludhiana
Water Drying Oven in Ludhiana – Frequently Asked Questions
Do you supply water drying ovens in Ludhiana?
Yes. SEW Surface Coating Pvt. Ltd. manufactures water drying ovens at its factory in Pune and supplies, erects and commissions them for customers across Ludhiana, Punjab.
Why is a water drying oven needed after pretreatment?
Any water left on the component after the final rinse causes blistering, pin-holes and poor adhesion once it is coated. The water drying oven removes all moisture so parts enter the coating booth completely dry.
Which water drying oven suits a dip pretreatment plant?
An in-line, tank-type oven placed after the last dip tank is the usual choice, because the same hoist or transporter loads it. For trolley-based plants a batch type oven is used.
What is a camel back oven?
It is a conveyorised oven whose article entry and exit are cut out parallel to the ground, so hot air stays inside the chamber. This reduces heat loss and fuel consumption.
Can you supply the pretreatment plant with the oven?
Yes. We supply the complete pretreatment plant, water drying oven, coating booth and curing oven as one line.
How is the plant delivered and installed in Ludhiana?
The plant is fabricated at our Pune works, about 1,750 km from Ludhiana by road. It is dispatched to your site, where our team erects and commissions it and carries out trial runs.
How do I get a quotation for a water drying oven in Ludhiana?
Send your component size and weight, pretreatment type, production rate and fuel available through our enquiry page, or call +91-99758 35066. Our engineers will prepare a layout and technical offer.
Other Products We Supply in Ludhiana
Water Drying Ovens in Other Locations
- Water Drying Oven in Baddi
- Water Drying Oven in Delhi
- Water Drying Oven in Gurugram
- Water Drying Oven in Noida
- Water Drying Oven in Faridabad
- Water Drying Oven in Rudrapur
- Water Drying Oven in Indore
- Water Drying Oven in Ahmedabad
Water Drying Ovens – main product page | All locations we serve
Need a Water Drying Oven in Ludhiana?
Share your component size and weight, pretreatment type, production rate and fuel available. Our engineers will send a plant layout and technical offer for Ludhiana.
Send Your Requirement Contact Us