Varnish Plant in Malaysia
SEW Surface Coating Pvt. Ltd. designs, manufactures and installs varnishing plants for manufacturers in Malaysia. Every plant is built at our own works in Pune, India, then export-packed and shipped to Malaysia, with erection and commissioning support from our engineers.
Varnish is a chemical used to insulate electrical goods such as motor windings, stators and transformer coils. A varnishing plant pre-heats the article in a moisture drying oven, dips it in varnish and then cures it in a varnish curing oven. Both ovens have solvent exhaust to maintain the LEL level.
- Moisture Drying Oven
- Varnish Curing Oven
- Solvent LEL Exhaust
- Exported to Malaysia
Varnish Plants for Malaysia's Industry
Malaysia's manufacturing is spread across the Klang Valley (Shah Alam, Klang), Penang's Bayan Lepas, Johor's Pasir Gudang, Kulim, Seremban and Melaka. Electrical and electronics, automotive, furniture, steel and aluminium makers are well established.
In Malaysia, demand for varnish plants comes mainly from electrical and panel makers, automotive and component makers and furniture and storage makers. Electrical windings must be free of moisture before they are varnished, and the varnish must be cured fully to give reliable insulation. Ovens with even air circulation and controlled temperature do both, batch after batch.
Electrical, electronics and furniture exporters need consistent, high-quality finishes.
Varnish Plant Equipment We Supply in Malaysia
Moisture Drying Oven
An enclosed insulated chamber with an air-circulating blower and electrical heater. It heats the article before it is dipped in varnish, so moisture is driven out of the winding.
- Air circulation for even temperature
- Electrical heating
- Solvent evaporation exhaust to maintain LEL level
Varnish Curing Oven
After dipping in varnish, the article travels through this oven for a set time so the varnish cures on it. The chamber has an air-circulating blower with electrical heater.
- Air circulation for even temperature
- Electrical heating
- Solvent evaporation exhaust to maintain LEL level
Typical Varnishing Process
A standard varnishing line follows this sequence:
- LoadingWindings, stators or coils are loaded on trays or the conveyor.
- Moisture DryingPre-heating drives moisture out of the winding.
- Varnish DippingThe hot article is dipped in varnish.
- DrainingExcess varnish drips off before curing.
- Varnish CuringThe article is baked until the varnish cures.
- Cooling & UnloadingParts cool and are inspected.
Oven size, temperature and residence time are set to your varnish type and the size of your windings.
Industries in Malaysia That Use Our Varnish Plants
Electrical & Electronics
E&E makers process enclosures and parts.
Typical requirement: Varnish curing ovens for transformer coils and electrical windings.
Automotive
Vehicle plants and suppliers process body and chassis parts.
Typical requirement: Varnishing of alternator, starter and EV motor windings.
Metal Furniture
Furniture exporters process metal frames.
Typical requirement: Varnish plant for electrical windings and coils.
Aluminium Extrusions
Extruders produce architectural and industrial profiles.
Typical requirement: Varnish plant for electrical windings and coils.
Steel Structures
Steel fabricators supply construction.
Typical requirement: Varnish plant for electrical windings and coils.
Varnish Plant Specifications
| Equipment | Moisture drying oven, varnish dipping and varnish curing oven |
|---|---|
| Construction | Enclosed insulated chamber |
| Heating | Electrical heaters with air-circulating blowers |
| Safety | Solvent evaporation exhaust system to maintain LEL level |
| Material handling | Trays, trolley or conveyor |
| Controls | Temperature controllers; PLC on request |
| Scope of supply | Design, manufacturing, erection and commissioning |
Final configuration is fixed after we study your component drawings, production rate and available floor space.
From Our Pune Works to Malaysia
Plants for Malaysia are fabricated and pre-assembled at our factory in Ranje, Pune, India. They are export-packed and shipped from Nhava Sheva (JNPT) port near Mumbai to Port Klang, and our engineers can travel to supervise erection and commissioning at your site.
- Technical study from your drawings, component details and production data
- Plant layout and process design in minimum floor space
- Fabrication and inspection at our Pune works
- Export packing and shipping documentation
- Erection and commissioning supervision by our engineers
Why Buyers in Malaysia Choose SEW Surface Coating
In-house manufacturing since 1996
Our own fabrication unit in Pune gives one-roof control over design, quality and delivery commitments.
25+ years in coating systems
More than two and a half decades of experience in powder and liquid painting systems for automobile, appliance, electrical, furniture and other industries.
Layouts in minimum space
We specialise in fitting a complete line into the floor space you actually have.
Low running cost
Plants are engineered for low fuel consumption, with options such as camel back ovens, solar-assisted heating and Waste Heat Recovery Systems (WHRS).
Modern technology
Nano-technology spray pretreatment, PLC-controlled transporters and SCADA monitoring are part of our installed base.
Export experience
We handle export packing and documentation and support erection and commissioning for customers in Malaysia.
Industrial Areas We Serve in Malaysia
Varnish Plant in Malaysia – Frequently Asked Questions
Do you export varnish plants to Malaysia?
Yes. SEW Surface Coating Pvt. Ltd. manufactures varnish plants at its factory in Pune, India, and exports them to customers in Malaysia, with erection and commissioning support from our engineers.
What is a varnish plant used for?
It insulates electrical goods such as motor windings, stators and transformer coils. The plant pre-heats the article, dips it in varnish and cures the varnish in an oven.
Why is a moisture drying oven needed?
Windings absorb moisture. The moisture drying oven heats the article before dipping so moisture is driven out and the varnish penetrates and bonds properly.
Are the ovens safe for solvent-based varnish?
Yes. Both ovens have a solvent evaporation exhaust system that keeps solvent concentration below the lower explosive limit (LEL).
Do you make other special ovens?
Yes. We also build special purpose ovens up to 800°C for baking, bonding, stress relieving and annealing.
How is the plant shipped to Malaysia?
The plant is fabricated at our Pune works, export-packed and shipped from Nhava Sheva (JNPT) port near Mumbai to Port Klang. Our engineers can travel to supervise erection and commissioning.
How do I get a quotation for a varnish plant in Malaysia?
Send your winding or coil size and weight, varnish type and batch or hourly output through our enquiry page, or call +91-99758 35066. Our engineers will prepare a layout and technical offer.
Other Products We Supply in Malaysia
Need a Varnish Plant in Malaysia?
Share your winding or coil size and weight, varnish type and batch or hourly output. Our engineers will send a plant layout and technical offer for Malaysia.
Send Your Requirement Contact Us