Powder Coating Plant in Nigeria
SEW Surface Coating Pvt. Ltd. designs, manufactures and installs complete powder coating plants for manufacturers in Nigeria. Every plant is built at our own works in Pune, India, then export-packed and shipped to Nigeria, with erection and commissioning support from our engineers.
A powder coating plant applies dry powder to metal parts with an electrostatic gun and then cures it in an oven to form a hard, even finish. We supply the whole line: powder coating booth, powder recovery system, after filter unit, curing oven, conveyor and the pretreatment plant before it. One company is responsible from layout to commissioning.
- Manual & Automatic Booths
- Cyclone Powder Recovery
- Batch & Conveyorised Ovens
- Exported to Nigeria
Powder Coating Plants for Nigeria's Industry
Nigeria is Africa's largest market. Manufacturing is concentrated in Lagos (Ikeja, Apapa, Agbara, Ikorodu) and Ogun State (Ota, Sagamu), with further industry in Kano, Port Harcourt and Onitsha–Nnewi.
In Nigeria, demand for powder coating plants comes mainly from oil and gas equipment makers, steel structure fabricators and furniture and storage makers. Powder coating gives a thick, durable coat in a single pass, contains no solvents, and overspray powder can be recovered and reused. That is why it has become the preferred finish for sheet metal, fabrications and aluminium sections.
Steel, roofing, furniture, oil and gas equipment, electrical and automotive makers are expanding local fabrication and coating.
Types of Powder Coating Booths We Supply in Nigeria
The booth is a fabricated MS or SS enclosure where powder is sprayed onto the article with an electrostatic gun. Overspray powder is drawn into a recovery system (mono-cyclone or multi-cyclone) so it can be reused.
Single Operator Booth
One operator sprays from the open face of the booth. It is compact, economical and easy to run, and works with both batch ovens and conveyorised lines.
Best for: Job coaters, fabricators and small to medium production.
Back-to-Back Operator Booth
Two operators work from opposite sides of a conveyorised booth, coating both faces of the article in one pass for higher output.
Best for: Conveyorised lines handling panels, frames and larger sheet-metal parts.
Automated Booth
Automatic guns coat the article as it moves through the booth on the conveyor, with manual touch-up where needed. Coating thickness is consistent from part to part.
Best for: High-volume auto component, appliance and enclosure production.
Powder Curing Ovens for the Complete Line
The curing oven is an enclosed, insulated chamber with air-circulating blowers and a heating system. Circulated air spreads an even temperature across the chamber so the powder melts, flows and cures properly.
Batch Type Oven
Coated articles are loaded on a trolley and pushed inside. After the baking schedule, the doors are opened and the trolley is taken out.
Best for: Mixed jobs, large fabrications and lower volumes.
Conveyorised Conventional Oven
The conveyor carries articles through the insulated chamber for a set time, so parts come out cured continuously.
Best for: Continuous production linked to the booth and pretreatment.
Conveyorised Camel Back Oven
It works like a conventional conveyorised oven, but the entry and exit are raised so hot air stays inside, reducing heat loss and fuel consumption.
Best for: Lines where running cost and fuel saving are the priority.
How a Complete Powder Coating Plant Works
A typical conveyorised plant follows the sequence below. Batch plants follow the same steps, with parts moved between stations by trolley or transporter.
- LoadingParts are hung on the conveyor or loaded in jigs.
- PretreatmentDip or spray degreasing, de-rusting and phosphating.
- Water Drying OvenRemoves all moisture before coating.
- Powder Coating BoothElectrostatic guns apply powder evenly.
- Powder RecoveryCyclone recovers overspray for reuse.
- After Filter UnitFilters fine powder before air is exhausted.
- Curing OvenPowder melts and cures at the set schedule.
- Cooling & UnloadingParts cool and are inspected and packed.
Stages are configured to your component, base metal, powder type and production rate.
Equipment Supplied With the Powder Coating Plant
After Filter Unit (AFU)
Filters out the fine powder particles (5 microns or less) that pass the cyclone, as required by Pollution Control Board norms, so clean air is exhausted.
Pretreatment Plant
Dip or spray pretreatment cleans and phosphates the metal surface so the coating adheres well and resists corrosion.
Water Drying Oven
Dries parts completely after the final rinse, since moisture left on the surface spoils the finish.
Pressurization Zone
Fresh air filtered in two or three stages is delivered around the booth to keep dust off the components.
Conveyor & Transporter
An overhead conveyor links pretreatment, drying, booth and oven. A PLC-controlled transporter is available for dip pretreatment.
Industries in Nigeria That Use Our Powder Coating Plants
Oil & Gas Equipment
Fabricators in Port Harcourt and Lagos supply the energy sector.
Typical requirement: Heavy-duty booth and batch oven for skids, panels and enclosures.
Steel & Roofing
Steel and roofing makers supply construction.
Typical requirement: Large walk-in booth with batch oven for long members and structures.
Steel Furniture
Furniture makers serve offices and institutions.
Typical requirement: Conveyorised line with dip or spray pretreatment and quick colour change.
Electrical & Panels
Electrical makers supply power and buildings.
Typical requirement: Back-to-back booth on a conveyorised line, or a single operator booth with batch oven.
Vehicle Assembly & Parts
Assemblers and part makers process chassis and body parts.
Typical requirement: Conveyorised plant with spray pretreatment and automated booth for brackets, chassis and body parts.
Powder Coating Plant Specifications
| Booth types | Single operator, back-to-back operator and automated booths |
|---|---|
| Booth construction | Fabricated MS or SS enclosure |
| Powder recovery | Mono-cyclone or multi-cyclone recovery system |
| Exhaust filtration | After Filter Unit (AFU) for particles of 5 microns or less, as per PCB norms |
| Curing ovens | Batch type, conveyorised conventional and conveyorised camel back |
| Oven heating | Heating system selected to suit cure schedule and the fuel available at your site |
| Material handling | Trolley (batch), overhead conveyor or PLC-controlled transporter |
| Pretreatment | Dip or spray, iron or zinc phosphate, or nano-technology chemistry |
| Clean-room option | Pressurization zone with two or three-stage filtered air |
| Energy saving | Camel back ovens, Waste Heat Recovery System (WHRS) and solar-assisted heating |
| Scope of supply | Design, manufacturing, erection and commissioning |
Final configuration is fixed after we study your component drawings, production rate and available floor space.
From Our Pune Works to Nigeria
Plants for Nigeria are fabricated and pre-assembled at our factory in Ranje, Pune, India. They are export-packed and shipped from Nhava Sheva (JNPT) port near Mumbai to Lagos (Apapa / Tin Can Island), and our engineers can travel to supervise erection and commissioning at your site.
- Technical study from your drawings, component details and production data
- Plant layout and process design in minimum floor space
- Fabrication and inspection at our Pune works
- Export packing and shipping documentation
- Erection and commissioning supervision by our engineers
Why Buyers in Nigeria Choose SEW Surface Coating
In-house manufacturing since 1996
Our own fabrication unit in Pune gives one-roof control over design, quality and delivery commitments.
25+ years in coating systems
More than two and a half decades of experience in powder and liquid painting systems for automobile, appliance, electrical, furniture and other industries.
Layouts in minimum space
We specialise in fitting a complete line into the floor space you actually have.
Low running cost
Plants are engineered for low fuel consumption, with options such as camel back ovens, solar-assisted heating and Waste Heat Recovery Systems (WHRS).
Modern technology
Nano-technology spray pretreatment, PLC-controlled transporters and SCADA monitoring are part of our installed base.
Export experience
We handle export packing and documentation and support erection and commissioning for customers in Nigeria.
Industrial Areas We Serve in Nigeria
Powder Coating Plant in Nigeria – Frequently Asked Questions
Do you export powder coating plants to Nigeria?
Yes. SEW Surface Coating Pvt. Ltd. manufactures powder coating plants at its factory in Pune, India, and exports them to customers in Nigeria, with erection and commissioning support from our engineers.
What equipment is included in a complete powder coating plant?
A complete plant usually includes a pretreatment plant, water drying oven, powder coating booth with cyclone recovery, after filter unit, powder curing oven and a conveyor or transporter system. A pressurization zone can be added for dust-free coating.
Which powder coating booth is right for my production?
A single operator booth suits job work and small to medium output. A back-to-back booth suits conveyorised lines coating both sides of larger parts, and an automated booth suits high-volume production where consistent thickness matters.
What is the difference between a batch oven and a conveyorised oven?
In a batch oven, coated parts are loaded on a trolley and baked for a set time with the doors closed. In a conveyorised oven, parts travel continuously through the chamber on the conveyor. A camel back oven is a conveyorised oven with raised entry and exit to reduce heat loss.
Why is an after filter unit needed?
Pollution Control Board norms do not permit powder to be exhausted directly to atmosphere from the cyclone. The after filter unit arrests the fine powder particles that pass the cyclone, so only clean air is released.
How is the plant shipped to Nigeria?
The plant is fabricated at our Pune works, export-packed and shipped from Nhava Sheva (JNPT) port near Mumbai to Lagos (Apapa / Tin Can Island). Our engineers can travel to supervise erection and commissioning.
How do I get a quotation for a powder coating plant in Nigeria?
Send your component size and weight, production rate, powder type and available space through our enquiry page, or call +91-99758 35066. Our engineers will prepare a layout and technical offer.
Other Products We Supply in Nigeria
Powder Coating Plants in Other Countries
- Powder Coating Plant in Ghana
- Powder Coating Plant in Uganda
- Powder Coating Plant in Kenya
- Powder Coating Plant in Ethiopia
- Powder Coating Plant in Egypt
- Powder Coating Plant in Tanzania
- Powder Coating Plant in South Africa
- Powder Coating Plant in Saudi Arabia
Powder Coating Plants – main product page | All locations we serve
Need a Powder Coating Plant in Nigeria?
Share your component size and weight, production rate, powder type and available space. Our engineers will send a plant layout and technical offer for Nigeria.
Send Your Requirement Contact Us